Vehicles
Sections
130 not categorized PORSCHE 930 A ARM BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1983-86 (includes uncategorized and accessory items) FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection FVD33150040 Replace worn-out original rear sub frame (side panel) bushings and return your car to its original ride quality with this cost effective alternative. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. If you are looking for a sportier upgrade we suggest our clubsport sub frame bushing set, part # FVD33150040r. We also sell complete sub frames with the bushings installed, part # FVD331993001.
$418.00
Make a selection FVD205993001HAG These bushings are made for h&r rear sway bars with 24 mm diameters. They are a direct replacement for our part # FVD205993001. If you would also like to replace the front, please use part # FVD205993001vag sold as a front set. 1 set needed per car.
$58.30
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection 99334101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34101802RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and re...(choose a part on the right to read more)
$440.00
Make a selection FVD205993001VAG
$58.30
Make a selection 10026448
$48.40
Make a selection 477511201BU
$108.90
Make a selection 150SPB968
$35.20
Make a selection 91410314100SET High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car.
From $103.40
Make a selection FVD059928944T
$47.30
Make a selection 90005212200
View/Change Diagram
From $53.90
Make a selection 90134378300EQ High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 4 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$6.60
Make a selection 61610314252SET8
$148.50
Make a selection 93010314715SET Oem parts, sourced directly from Germany. Sold individually. 1 necessary per car.
$112.20
Make a selection FVD0599249441
$56.10
Make a selection 92810513902EQ
$45.10
Make a selection 92810561304
View/Change Diagram
From $22.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |